口模,die英語短句,例句大全

口模,die
1)die[英][dai][美][da?]口模
1.Design of Plastic Profile Extrusion Dies;塑料異型材擠出口模設計
2.Preliminary study of extrusion die design by rheology擠出口模設計中的流變學初步研究
3.By means of the visualization device,the flow trajectories of polymer melts in an cuneiform convergent extrusion die were recorded by video.利用可視化實驗手段,動態拍攝了楔形收斂擠出口模內聚合物熔體的流動軌跡線,借助于軌跡線,分析了熔體在口模中的流動狀態,同時通過實驗得到了熔體在口模過渡區內的停留時間與擠出流量之間的關系。

英文短句/例句

1.FS Switch to full screen mode. /WM Switch to window mode.FS切換到全屏模式./WM切換到窗口模式.
2.Deep Web Form Schema Extraction and Schema IntegrationDeep Web入口模式抽取與模式集成
3.The Design of Router s Interface Module--The Design of Ethernet Module and Ethernet Module;路由器接口模塊設計——Ethernet模塊和ISDN模塊的設計
4.Population and Development Simulation Model人口與發展模擬模式
5.This interface should be placed in the interfaces module of the messageboard.該接口將代替留言薄的模塊接口。
6.module interface cross-reference模塊接口相互對照引用
7.password protected load module file口令保護裝入模塊程序
8.type genus of the family Catostomidae.亞口魚科的一個模式屬。
9.simulate voice synthesizer模擬口聲語音合成器
10.container terminal capacity model集裝箱港口容量模型
11.monolithic D/A interface單片式數字模擬接口
12.storage module drive interface存儲模塊驅動器接口
13.input/output interface control module輸入輸出接口控制模塊
14.Population-Household Consumption Projection人口－住戶消費預測模式
15.A: We brought fruit juice.口試模擬實戰演練（一）
16.Integrated Macro Model for Population and Development人口與發展綜合宏觀模式(人口發展宏觀模式)
17.Simulation Model on Population and Development (Game of Training)《人口與發展模擬模式》（訓練游戲）
18.A/D,D/A Interface of Single Board Microcomputer andIts Application單板微型機的模/數、數/模接口及其應用

相關短句/例句

expanding and necking die擴口、縮口模
1.According the structure characteristics of oil filling pipe,combining production experience,designed expanding and necking die.針對加油管的結構特點,結合企業生產經驗,給出了連續擴口、縮口模設計方案。
3)gate[英][ɡe?t][美][get]澆口，進模口
4)inlet[英]['?nlet][美]['?n'l?t]進模口，閘口
5)riser gate冒口進模口
6)Die design口模設計
1.After an analysis on the velocity distribution obtained from numerical simulation, the original die design was modified;and the length of each part of molding zone was determined according to the principle of flow rate equilibrium.研究還表明:對于異型材擠出口模設計,不能把口模截面視作若干規則形狀截面的簡單幾何組合,必須把其當成一個整體來對待;過渡區不僅影響成型區的流動,而且對穩流區的流動也有不可忽視的影響,設計時應對過渡區給予足夠的重視。
2.The gas-assisted extrusion,fiber spinning,hollow fiber and microporous membrane technology were contacted for the first time,and the actuality of these technologies and the characteristics of die design were introduced breifly at home and abroad.首次將氣輔擠出、纖維紡絲、中空纖維及微孔薄膜技術聯系起來,并簡要介紹了國內外這些技術的研究現狀和口模設計的特點。