1)cutterhead刀盤
1.Principle and Maintenance of Cutterhead Control System of Shield Machine;盾構機刀盤控制系統的機理與維護
2.Three-dimensional Cutting Simulation by Cutterhead of Shield Machine Based on Parallel Computing;基于并行計算的盾構機刀盤三維切削仿真
3.Calculation of cutterhead torque for EPB shield and the relationship between cutterhead torque and shield driving parameters土壓平衡盾構刀盤扭矩計算及其與盾構施工參數關系研究
英文短句/例句
1.spread-blade bevel gear cutter螺旋傘齒輪切削刀盤
2.curve-tooth bevel gear milling弧齒錐齒輪銑刀盤刃
3.Decision and Application of Rock-breaking Trajectory of Disc Cutter on Spheric Holder球面刀盤上盤形滾刀破巖曲線的確定及應用
4.Research on the Prognosis and Health Management and Application of TBM Disc CuttersTBM刀盤上盤形滾刀健康管理理論及應用研究
5.Study on Cutters Layout Rules of EPB Shield Cutter-Head某型土壓平衡盾構刀盤布刀規律研究
6.Selection of shield cutterhead and tool for Chengdu sand-pebble layer成都砂卵石地層盾構刀盤與刀具選擇
7.Please check the up-cutter-head of knife at the notch part is whether rightly opposite to the necking of down-cutter-head or not ,and no binding phenomenon.請檢查開槽部上刀盤的刀片是否與下刀盤的刀槽對正,運行時無卡滯現象.
8.Design and Research on Cutter Layout and the Structural Parameters of the Cutterhead Optimization for TBMTBM滾刀布置與刀盤結構參數優化設計研究
9.Study of Cutter Layout Design of Full-face Rock Tunnel Boring Machine全斷面巖石隧道掘進機刀盤刀具布置方法研究
10.The Analysis of Abrasion Cutter Head of Large Diameter TBM in Complex Ground復合地層大直徑盾構刀盤刀具磨損分析
11.Side-slip Analysis of Disc Cutter on All Kinds of Cutterheads ofFull Face Rock Tunnel Boring Machine掘進機不同刀盤面上盤形滾刀工作時的側滑分析
12.spiral bevel milling cutter head sharpening machine螺旋錐齒輪銑刀盤刃磨床
13.ground-working disk blade切土圓盤刀，耕耘圓盤
14.shoulder cutter切割豬肩肉用的圓盤刀
15.rotary gang slitting帶材多刀圓盤剪縱剪切
16.semi auto lathe with chuck and multitools卡盤多刀半自動車床
17.cutting blade for agricultural machines (excl. coulters for ploughs and discs for harrows)農業機械用刀片（不包括犁刀和耙盤）
18.The English place the knife in the middle of the plate with its point on the plate and the fork beside it, points turned up.英國人把刀子放在盤子中央，刀尖在盤上，叉子放在刀子旁邊，尖朝上。
相關短句/例句
cutter head刀盤
1.In designing the power system of shield tunneling machine,a good calculation model is needed to forecast the cutter head torque in different earth layers.在盾構驅動系統設計時,需要研究刀盤扭矩的準確計算模型,以便預測不同土層掘進時的刀盤驅動功率。
3)cutter[英]['k?t?(r)][美]['k?t?]刀盤
1.Designing and optimizing of the cutter of developing parallel link excavating shield driven by hydraulic cylinder;液壓缸驅動式偏心盾構刀盤掘進機構設計和優化
2.Study on klingelnberg bevel gear interfere with the cutter in process;克林根貝格螺旋錐齒輪刀盤干涉的研究
3.Analysis and comparison were made of cutter types, support modes, torque, driving force and arrangement of jacks, spiral conveyor and slurry and foam feeder, to ensure selection of proper shield.根據無水砂卵石地層的特點及盾構機的適應性,確定選用加泥式土壓平衡盾構,在此基礎上,對盾構的刀盤形式、支撐方式、扭矩、千斤頂的推力及配制、螺旋輸送機及加泥加泡沫系統等進行分析和比較,保證盾構的準確選型,對類似地層條件下的盾構參數計算和選型具有一定的參考意義。
4)cutting wheel刀盤
1.During the Xiao-song shield machine drills through the Pearl River which part belongs to Xiaoxin section works of Guangzhou Metro line 4, the cutting wheel of the shield machine has worn badly though the cutters are replaced continually, however, the geology below the river can t provide the conditions with repairing the worn cutting wheel.小松盾構機在廣州地鐵四號線小新盾構區間段穿越珠江的過程中,雖然頻繁換刀,刀盤仍然磨損嚴重,而江底的地質狀況又不具備修復刀盤的條件,本文正是針對珠江江底這種特殊的地質條件,討論如何在江底創造敞開式開倉條件,以修復刀盤、更換刀具。
2.This paper has analyzed the hydraulic system of the cutting wheel and screw conveyor in test tunneling machine, and the integration of the hydraulic system.介紹了所設計實驗盾構的刀盤與螺旋機驅動液壓系統的工作原理與系統集成,該系統是開式液壓系統,應用電液比例控制技術對泵捧量進行實時調節,通過二通插裝閥技術實現了高壓、大流量液壓控制系統的集成。
5)disc cutters盤刀
6)shield cutter刀盤刀具
延伸閱讀
刀刀1.動搖貌。
