上拱度,camber英語短句,例句大全

上拱度,camber
1)camber[英]['k?mb?(r)][美]['k?mb?]上拱度
1.Study on the prestress concrete beam camber under different creep modes;不同徐變模式下預應力混凝土梁上拱度的研究
2.By analyzing measured value of the camber and theoretical value of camber of RPC low-altitude T-beam at the stretching stage,a comparison certifies that the pre-stress s stress is controlled accurately,and the loss of pre-stress is cal- culated correctly,which means the theoretical calculation method of camber is feasible.對RPC低高度T形梁張拉階段梁體上拱度試驗實測值和理論計算值進行對比分析,兩者符合較好,證明了該梁預應力張拉控制得比較準確,預應力損失的計算方法得當,上拱度的理論計算方法是可行的。
3.Under the action of a prestressing force,the camber deformation of a PC simply supported girder develops slowly due to concrete creep effect.如果對于徐變變形的預測不準,在運營階段梁體徐變變形的發展將會引起橋面的立面線形不平順,嚴重影響行車安全和旅客舒適度,甚至將造成梁體上拱度過大而無法使用。

英文短句/例句

1.The Uncertainty Estimation for Measuring Crane Beam’s Camber起重機主梁上拱度測量不確定度的評定
2.Creep and Upward Calculation of Prestressed Concrete T Beam預應力混凝土T梁徐變及其上拱度計算
3.The superstructure has a depth of 3 ft. 6 in. with a marked camber of 19ft. 8 in.上部結構的建筑高度為3英尺6英寸，有19英尺8英寸顯著的上拱度。
4.Research on Centering Construction Simulation Applied in Long-span Stone Arch Bridge with ALGOR R12大跨度石拱橋拱架施工仿真分析在ALGOR R12上的實現
5.Factorial Analysis for Camber of T-shape Precast-beam in Resting Period預制T梁存梁期間上拱撓度影響因素分析
6.Research on the Key Technologies for Design of Continuous Welded Rails(CWR) on Large-span Basket Handle Arch Bridge大跨度提籃拱橋上無縫線路設計關鍵技術研究
7.Analysis of Seismic Response of Deck Type Long-span CFST Arch Bridge上承式大跨度鋼管混凝土拱橋地震反應分析
8.an arch whose jambs are not at right angles with the face.拱的側板與拱的正面搭配角度不對的拱。
9.The Arched Bridge Arches Constructs Participates in the Host Arch Ringjoint Action Research;拱橋拱上建筑參與主拱圈聯合作用研究
10.Ultimate Bearing Capacity Analysis of Long-Span Stone Arch Bridge with Arched Spandrel Structure大跨徑拱式拱上結構石拱橋極限承載力分析
11.a arch whose height is less than half its width.高度不及寬度一半的拱。
12.Either of the sides of an arch, curving down from the apex to an impost.梁腋，拱腋拱門上任意一個從拱頂到拱墩間的部分
13.Comprehensive optimization of joint closure temperature field and its shape for arch dam拱壩封拱溫度場及體形綜合優化方法
14.This tongue causes the flat autochthonous beds below to appear arched upward because of velocity pull-up.就是這個巖舌造成它下面的原生地層由于速度的急增而向上拱起。
15.The Analysis of Alignment Control and Stability of Long-span Concrete-Filled Steel Tube Deck Arch Bridge under Construction;大跨度上承式鋼管混凝土拱橋施工過程線形控制及穩定分析
16.Earthquake response analysis of long span steel deck arch bridge considering effects of elasto-plastic finite displacement考慮雙非線性影響的大跨度上承式鋼拱橋地震響應研究
17.The upper or exterior curve of an arch.拱背線拱頂上面或外緣的曲形線
18.An arch over an entrance or passageway.拱門，牌樓入口或通道上的拱頂

相關短句/例句

deflection upwards上拱度
1.Analysis and control on the deflection upwards of large prestressed concrete aqueduct;大跨預應力混凝土梁式渡槽結構上拱度的分析與控制
2.The influence on the deflection upwards of concrete shrinkage, creep and temperature in prestressed concrete bridges were researched by experimental observation.結合武漢繞城高速公路的橋梁施工工程 ,選取 30 m預應力混凝土 T梁作為研究對象 ,通過開展對梁內應變的觀測和梁上拱度的長期測量觀測的試驗研究 ,探討了混凝土收縮、徐變和溫度等因素對預應力混凝土梁上拱度的影響以及預應力混凝土梁上拱度隨時間的變化規律 ,為預應力混凝土梁橋的設計和施工提供了參考依據。
3)allowed camber允許上拱度
4)swell[英][swel][美][sw?l]上拱
1.Pot shell swelling during pot start-up;電解槽啟動期間的槽殼上拱
5)Long-span top-bear arch bridge大跨度上承式拱橋
6)camber[英]['k?mb?(r)][美]['k?mb?]拱度
1.This article introduces the author how to use cable sling, height gauge together with water level to measure girder s camber of bridge crane, and expatiates the operation process in detail.簡介了筆者用水準儀結合吊鉤掛放吊尺測量橋式起重機主梁拱度的探索過程,詳細介紹了此法的具體操作步驟,并對此法在測拱過程中的諸多技術性問題及測量結果的準確度進行了比較深入的討論與論證。
2.In order to solve the problem that the prefabricated camber size of main girder\'s web plate on aluminum electrolysis multifunctional unit is too big or small,resulting in climbing or gliding problem of tapping trolley and tool trolley during production.針對鋁電解多功能機組主梁腹板預制拱度過大或過小、導致生產中出鋁小車和工具小車運行時發生爬坡或下滑的問題,根據由理論計算的主梁跨中靜撓度值以及與主梁焊接時引起拱度值變化的實際經驗,給出確定主梁腹板預制拱度的一種方法,此方法解決了生產實際中出現的問題。
3.Girder camber is a important technical condition of Pot Tending Machine(PTM),dimensions of girder camber affects directly run of tool car and Aluminum car.主梁拱度是鋁電解多功能機組一個重要的技術條件,主梁拱度的大小直接影響到工具小車和副小車的運行,在主梁的制造過程中,要合理的安排組裝順序、焊接順序,并采用特殊工藝進行焊后修復,以保證主梁拱度的技術要求。