1)deflection[英][d?'flek?n][美][d?'fl?k??n]撓曲
1.An theoretical analysis and experimental verifications are made to investigate the folding deflection behavior of inflated tubes.對充氣展開管的彎折撓曲特性進行了理論分析和實驗驗證。
2.Based On the first-order shearing theory , he deflection and bucking of a laminatedbeam under axial pressure are studied and the solutions in closed form for the beam deforma-tion have been obtained.在一階剪切理論基礎上，研究了疊層梁受軸壓的撓曲和屈曲問題，得到該問題的封閉解，并將固支、簡支、懸臂梁的屈曲載荷和對應的經典理論解聯系起來，統一于一個表達式。
3.In this paper,superposition method and Galerkin method are applied to study the deflection of elastic thin plate.本文分別應用迭加法和迦遼金法計算矩形彈性薄板的撓曲問題,結合均勻分布載荷作用下四邊固定彈性薄板的計算過程,將兩種算法得到的結果分別與其精確解作比較,體現出迭加法易于理解、便于運用的優點。
英文短句/例句
1.flexural fatigue彎曲疲勞,撓曲疲勞
2.flexural strain撓曲應變,彎曲應變
3.flexural resilience彎曲回彈性,撓曲回彈性;彎曲回彈能,撓曲回彈能
4.crossbreaking strength橫斷裂強度, 撓曲強度
5.Flexural Modulus - 1% Secant (Based on ASTM D 790A)撓曲模量–1%正割（根據ASTMD790A）
6.nonlinear flexible spacecraft非線性撓曲宇宙飛船
7.flex cracking test（涂層的）耐屈撓龜裂強度試驗,撓曲疲勞試驗
8.ANALYTIC SOLUTION OF BENDING SURFACE PROBLEM OF FAN-SHAPED PLATE扇形薄板彎曲問題撓曲面的解析解
9.A still more difficult distinction is that between a sharp flexure and a fault.區別尖銳的撓曲和斷層更加困難。
10.Bend the end of the wire back.將這根金屬線的末端向后撓曲。
11.testing methods for flexural strength of adhesives膠粘劑粘結撓曲強度的試驗方法
12.Minimum of three inner wraps to prevent buckling.最少三層內部包裹，有利于防止撓曲。
13.Howerer, under heavy load the shaft may deflect excessively.但是，在重載作用下，軸會發生過度撓曲。
14.testing method for abrasion resistance of textile fabrics: flexing and abrasion method植物耐磨性試驗法：撓曲磨損法
15.Buckling Analysis of a Bottom Supported Main Vessel of FBR底部支撐的快堆主容器撓曲分析(英文)
16.The Theoretical Study of the Felxoelectric Effect in Nematic Liquid Ctystal;向列相液晶中撓曲電效應的理論研究
17.The Flexoelectric Effect and the Anchoring Energy of the NLC Cell;撓曲電效應與向列相液晶盒的錨定能
18.Generally Spiral Trajectory Curvature Center of Curvature and Torsion一般螺線曲率中心軌跡的曲率與撓率
相關短句/例句
flexure[英]['flek??][美]['fl?k??]撓曲
1.In order to know the low temperature performance of polyfluortetraethylene used as sealing material,the mensuration is done that constriction plate and tubular test piece, and of plate flexure in the range of -100 to -40℃.為了考查聚四氟乙烯用做密封材料時的低溫性能,在-40至-100℃的溫度范圍內,分別對板狀和管狀試件的收縮以及板狀試件的撓曲進行了測定。
2.The nonlithostatic stresses, regions of failure and flexure profiles have been computed as the upper crustal layer is extended by progressive increments.計算了以一定增量逐漸拉伸上地殼層時各個階段的非靜巖應力 (Nonlitho staticstress)、塑性破裂 (Plasticfailure)分布及撓曲剖面 (Flexureprofile)。
3.Compensating For the Super-Long Precision Rubbing Rollor’s Flexure對TFT-LCD摩擦設備的超長精密摩擦滾子進行變形量計算和測量,采用切削補償的方法可以有效地抵消摩擦滾子因自重產生的撓曲變形,提高摩擦質量。
3)deformation[英][,di:f?:'me??n][美]['dif?r'me??n]撓曲
1.In this paper,superposition method is applied to the study of the deformation of elastic thin plate with two fixed adjacent sides: one freelysupported side,the other free side under uniform pressure.運用迭加法計算均布載荷作用下相鄰兩邊固定,一邊簡支,另一邊自由矩形彈性薄板的撓曲問題,結合有限元分析軟件ANSYS數值模擬的結果,驗證該板型用迭加法所得結果的精確性,分別分析迭加法和數值模擬技術的優點和不足,進而說明迭加法和數值模擬技術有效結合的長處,及其對實際工程和彈性薄板的理論研究具有特別重要的意義。
2.Caculatim of vary section beam deformation data, at present, complicated in theory analysies, numerous work to be done, so error occurred in some caculation is normal.目前變梁撓曲常數的計算,理論復雜計算量大,因而已有文獻中出現計算誤差是難免的,載荷彎矩圖法是精確法,物理概念清楚,計算簡單并有核算方法。
4)torsion[英]['t?:?n][美]['t?r??n]撓曲
5)deflexion[英][di'flek??n][美][d?'fl?k??n]撓曲
6)bending[英][bend][美][b?nd]撓曲
延伸閱讀
撓曲1.屈曲。
