1)crankshaft[英]['kr??k?ɑ:ft][美]['kr??k'??ft]曲拐軸
1.Computing method on strength analysis of combination typed tri-crankshaft;組合式三曲拐軸的強度分析計算方法
2.Mechanics analysis based on crankle instead of crankshaft;活塞壓縮機曲柄軸改曲拐軸的力學分析
英文短句/例句
1.Thus a normal loom has two shafts. The main shaft(crankshaft or top shaft) drives the lay mechanism and is geared to another shaft which operates at half of the speed of the crankshaft.這樣,普通織機應具備兩根軸,主軸(曲拐軸或位于上部的軸)驅動筘座并通過齒輪驅動另一根軸。
2.Analysis of Inspection and Measuring Method for 120° Distributing Angle Errors of Crankshaft Crankpins曲軸曲拐120°角度誤差檢測方法分析
3.Research on the Upset Forging Technology of Marine Crank of 305 Crankshaft船用305曲軸曲拐鐓鍛成形工藝研究
4.Research on a Newly Combinational Tri-turned Crankshaft for Diaphragm Pump新型組合式隔膜泵用三拐曲軸的研究
5.Analysis on Measuring Accuracy in Inspecting Crank Angles for Six-cylinder Crankshafts六缸發動機曲軸曲拐夾角檢測方法的精度分析
6.Study on Making Process and Mould Structure of None-phase Angle Crankshaft with Four Cylinder Sleeve無相位角四拐曲軸的制坯工藝及模具結構優化
7.crankshaft (main journal turning lathe)曲軸（主軸頸）車床
8.triple-barrel pump三聯式筒泵(三個泵筒與一個吸液管相連，由三拐曲軸驅動三個活塞產生均勻液流)
9.upper center crankshaft bearing曲軸主軸承上中軸瓦
10.Inflection Point拐點，彎曲點，轉折點
11.Full of twists and turns;tortuous.彎彎曲曲的；迂回的充滿彎曲和拐彎的；曲折的
12.crankshaft journal face hardening machine曲軸軸頸表面淬火機床
13.Crankshaft main journal out of round or worn曲軸主軸頸不圓或磨損
14.crankshaft journal milling machine曲軸軸頸銑削專用機床
15.Replace crankshaft or grind journals更換曲軸或磨光軸頸
16.The feed holes for the crankshaft main bearings.曲軸主軸承進入口。
17.Crankshaft and main bearings service曲軸和主軸承的維修
18.crankcase cam gear bushing曲軸箱凸輪傳動軸襯套
相關短句/例句
Four crank四曲拐軸
3)split-pin crankshaft錯拐曲軸
1.Influence of Constraint Condition on FEA for Split-Pin Crankshaft;約束條件對錯拐曲軸有限元分析的影響
2.The general methods for the balancing analysis of inertia forces in the internal combustion engine(ICE) that adopted split-pin crankshaft technology was studied in this paper.針對某V6柴油機,對比分析了該柴油機采用錯拐技術前后傾覆力矩及慣性力系的變化情況,結果表明,錯拐曲軸平衡技術可有效抑制內燃機內部的激勵載荷,是改善內燃機振動、噪聲特性極為有效的技術措施之一。
4)Stagger crankshaft錯拐曲軸
1.Using ANSYS software, the finite element analysis for the stagger crankshaft of a 60°V6 vehicle gasoline engine was conducted under extreme operation conditions.應用ANSYS軟件,對某60°夾角V6車用汽油機的錯拐曲軸進行了不同極限工況下的有限元計算,尤其對該曲軸的載荷和約束條件做了較為詳細的討論,得到了該錯拐曲軸的應力分布,并校核了其靜安全強度。
2.The structural strength difference between stagger crankshaft and common crankshaft and the influence of Various loads and different sliding bearing clearances on stagger crankshaft strength are studied.以90°夾角的某V型6缸柴油機為例,應用有限元分析方法,研究探討了采用錯拐結構前后曲軸強度的變化,以及不同載荷、不同主軸承間隙等因素對錯拐曲軸強度的影響,并通過實驗驗證了有限元分析的正確性。
3.The analytical method based on FEA and experiments is used to study the structural strength of diesel engine stagger crankshaft.通過對比表明:理論分析與實驗實測結果具有較好的一致性,針對錯拐曲軸所采用的計算分析方法與實驗方法均是合理可行的。
5)crankshafts/single crank throw曲軸/單拐
6)five staggers crankshaft五拐曲軸
1.Free-forging process research on five staggers crankshaft of natural gas compressor;天然氣壓縮機五拐曲軸自由鍛工藝研究
延伸閱讀
脖子拐1.見"脖拐"。
