內嚙合,internal-meshing英語短句,例句大全

內嚙合,internal-meshing
1)internal-meshing內嚙合
1.The outer rotor has the trend of revolution along the inner rotor and this trend must be overcome by the cylinder via the action of a support force in an internal-meshing rotary cycloid compressor.為了限制內嚙合擺線轉子壓縮機中外轉子繞內轉子公轉的趨勢,在外轉子上施加一個支撐力,對支撐力的位置進行了詳細分析。
2.The contact force of internal-meshing gear compressor between gears directly affects the choice of gears materials,friction power and operating reliability.為了使內嚙合壓縮機的材料選擇準確、摩擦功耗減小、運行可靠性提高等,采用線彈性理論,在分別考慮缸體與外轉子無間隙和有間隙的2種情況下,建立了齒面接觸力計算的數學模型,該模型比有限元方法求解簡單,并可得到接觸力隨轉角的變化關系,特別是易于根據計算得到的結果合理設計和優化型線參數。
3.The relationship between the volume of working chambers and rotating angles is the basis to do the thermodynamic calculation for the internal-meshing rotary compressor.內嚙合轉子壓縮機工作腔容積和轉角變化的關系是進行壓縮機熱力計算的基礎,目前還缺乏相應的計算公式。

英文短句/例句

1.quiet internal gear pump低噪聲內嚙合齒輪泵
2.Study on the Meshing Characteristics and CAD Technique of Cycloidal Gear Pump;內嚙合齒輪泵嚙合特性分析及CAD技術研究
3.internal spur gear內嚙合圓柱齒輪，直齒內齒輪
4.Study on the Theory and Simulation of Cycloidal Pump;內嚙合擺線齒輪泵的理論研究與仿真
5.Spin-forming numerical simulation of cup-shaped inner meshing gear杯形內嚙合齒輪旋壓成形的數值模擬
6.Kinematic analyse of inside engaged gear based on ADAMS基于Adams/View的內嚙合齒輪運動學仿真
7.Research on Designing System of Internal Meshing Cycloidal Pump on Network;基于網絡的內嚙合擺線齒輪泵設計系統研究
8.The Research on Geometrical Parameter and Flow Pulsation in Internal Gear Pump;內嚙合齒輪泵幾何參數及流量脈動的研究
9.Study on Constructure and Characteristic of Internal-Meshing Few Differences Teeth Gear Hydro-Motor;內嚙合少齒差液壓馬達的結構與特性分析
10.Influence of Internal Gear Pump's Floating Plate on Pump's Service Life and Efficiency內嚙合齒輪泵浮動側板對泵壽命及效率的影響
11.The effect on internal gear-pair actual meshing by the basic parameters of gear齒輪基本參數對內嚙合效率影響的研究
12.Reliability Design of Involute Zero-tooth-difference Internal Gear Mechanism漸開線零齒差內嚙合齒輪機構的可靠性設計
13.Continuity Condition of Profiles for Internal-Meshing Cycloid Rotary Compressor內嚙合擺線轉子壓縮機型線連續性條件研究
14.Integrated Performance Research for Inner-engaged Oil Pump with Shifting-engine基于提高內嚙合-擺線轉子式機油泵綜合性能的研究
15.Since there is deviation of gear angle, gear box may be damaged while starting engine.但由于變速箱內嚙合角度的偏差,起步驅動時會造成變速箱損壞。
16.The Optimization of Inner Meshed Gear Pump with Wedge and External Circle-arc and Its Envelope Teeth楔塊式外圓弧及其包絡線內嚙合齒輪泵的優化設計
17.Design of Involute Zero-Tooth-Difference Internal Gear Mechanism and Measure Method;漸開線零齒差內嚙合齒輪副的設計及測量方法研究
18.Computer-Aided Geometric Design and Parameters Optimization of Internal Gear Pairs with Small Teeth Difference;少齒差內嚙合齒輪的計算機輔助幾何設計及參數優化

相關短句/例句

internal gearing內嚙合
1.By using geometry analysis method,this paper educed calculation formula of normal direction gear side clearance when internal gearing involute gear transmission center distance waned slightly.通過幾何分析的方法,導出了內嚙合漸開線齒輪傳動中心距略變小時,法向齒側間隙的計算公式,供齒輪傳動設計計算之用。
3)internal toothing內齒嚙合
4)inner meshing gear內嚙合齒輪
1.Numerical simulation of the influence of the processing parameters on the spin-forming of the inner meshing gear of cups;工藝參數對杯形內嚙合齒輪旋壓成形影響的數值模擬研究
2.Spin-forming numerical simulation of cup-shaped inner meshing gear杯形內嚙合齒輪旋壓成形的數值模擬
5)interior meshing displacement內嚙合變位
6)internal coupling spline內嚙合花鍵