開孔接管,Nozzle英語短句,例句大全

開孔接管,Nozzle
1)Nozzle[英]['n?zl][美]['nɑzl?]開孔接管
1.Prediction of the Stress Concentration Factors of the Nozzles on the Internal Pressure Cylinders;內壓筒體開孔接管結構應力集中系數預測
2.The method for generating 3-D FEM mesh for pressure vessels with nozzle;開孔接管結構三維有限元建模方法

英文短句/例句

1.STRESS STRENGTH EVALUATION OF REINFORCED STRUCTURE OF THE NOZZLE OF E-330 A PROCESS INLET LINEE-330A工藝入口管線開孔接管應力強度評定
2.Thin Shell Theory Solutions of Two Normally Intersecting Cylindrical Shells for Large Diameter Ratio and Its Verification;圓柱殼大開孔接管的薄殼理論解及其實驗驗證
3.Stress analysis of Opening Tubing Connection Zone for High Pressure Vessels Based Finite Element;基于有限元的高壓容器開孔接管區應力分析
4.Thermal Stress Analysis of the Opening Tubing Connection of Steam Header of Boiler in a Power Plants電廠鍋爐集箱開孔接管部位的熱應力分析
5.welded reinforcement of nozzle opening接管開孔的焊接補強
6.openings for pipe connections用于管子連接的開孔
7.openings through welded joints通過焊接連接處的開孔
8.Three-Dimensional FEA of Large Opening Cylinder with Flatting Nozzle;大開孔率圓柱殼平齊接管結構三維有限元分析
9.3-D Elastic and Plastic FEM Analysis of Hydraulically Expanded Tube-to-Tubesheet Joints with Tubesheet Hole Groove;管板孔開槽的液壓脹接接頭三維彈塑性有限元分析
10.RIGHT DOOR KEY CYLINDER SWITCH CONNECTOR右門鑰匙插孔開關接頭
11.Research on Stress Analysis and Reinforcement Design of Spherical Shell with Transnormal Flush Nozzle;球殼超標開孔平齊接管應力分析與補強設計研究
12.REINFORCEMENT CALCULATION METHOD FOR LARGE OPENING PRESSURE CYLINDER VESSEL WITH FLANGE CONNECTION帶法蘭接管的壓力容器圓筒大開孔補強計算方法
13.STUDY ON THE INFLUENCE OF NOZZLE-VESSEL THICKNESS RATIO ON LARGE OPENING IN PRESSURE VESSELS接管與筒體壁厚比對壓力容器大開孔應力的影響
14.openings for connections to brazed vessels用于對釬焊容器的連接開孔
15.TRUNK KEY CYLINDER SWITCH CONNECTOR (HARNESS SIDE)行李箱鑰匙插孔開關接頭（配電盤側〕
16.In a general sense peacocks are a symbol of openness And acceptance.一般來講，孔雀象征著開放和接受。
17.(CAVITY 3) TO GROUND (CAVITY 5).（孔３）接地（孔５）。
18.height of nozzles and M.H. from outside vesse接管與人孔離容器外側高度

相關短句/例句

opening tubing connection開孔接管
1.A three dimensional(3D) finite element method is used to analyze the stress on opening tubing connection on pressure vessels,the stress distribution information of vessel barrel,tubings and position of connection are obtained.對壓力容器開孔接管區進行了三維有限元分析,獲得了容器筒體、接管及其連接部位的應力分布信息。
2.Based on the practical situation of the steam header of boiler in a power plant,a 3D model of the opening tubing connection of steam header of boiler is built by using software of PRO/E,and extending experiment at room temperature and at high temperature for 12Cr1MoVg is carried out.主要根據某電廠鍋爐集箱實際情況,采用PRO/E軟件建立了鍋爐集箱開孔接管部位的三維模型,進行了電廠鍋爐集箱常用材料12Cr1MoVg的常溫和高溫拉伸試驗,分析了集箱的受力情況,以及鍋爐集箱開孔接管部位的1/4三維模型的熱應力,得到了其最大應力的分布規律,指出了集箱裂紋產生的原因和位置及其發展趨勢。
3)nozzle openings接管開孔
4)nozzle (see Nozzle opening)接管(見接管開孔)
5)vessel-nozzle junction開孔接管區
6)cylinder-nozzle intersection開孔-接管區
1.Experimental study of elastic stress of cylindrical shell cylinder-nozzle intersection under combined loadings;組合載荷作用下開孔-接管區彈性應力試驗研究