1)manipulator[英][m?'n?pjule?t?(r)][美][m?'n?pj?'let?]工作臂
1.Operation trajectory of harvester manipulator林木采伐機工作臂的工作軌跡
英文短句/例句
1.Research on stability of folding-telescopic arm for aerial work platform高空作業車折疊伸縮混合式工作臂穩定性分析
2.Research on Obstacle-avoidance System of Performance Arm of Intelligent-video Bridge-detection Vehicle;智能視頻橋梁檢測車工作臂避障系統的研究
3.Study on Obstacle-avoidence Control of Performance Arm of Intelligent-video Bridge-detection Vehicle智能視頻橋梁檢測車工作臂避障控制的研究
4.Boom swing device enables a larger work range.動臂帶偏轉置，適應更大的工作范圍.
5.17 She sets about her work vigorously; her arms are strong for her tasks.她精神飽滿地投入工作，她雙臂有力。
6.The Operating Principle and Design for Auto-Interruption Regulating Arm自動間隙調整臂工作原理及設計方法
7.Optimum design of hooklift working device based on virtual prototype虛擬樣機的拉臂車工作裝置優化設計
8.Reliability for Microcantilever Device Manufacture Craft微懸臂梁器件制作工藝的可靠性研究
9.Research on Fabrication of Silicon Micro-cantilevers based on MEMS Technology基于MEMS技術硅微懸臂梁制作工藝研究
10.Mechanics Analysis of Working State of Active Arm Frame of Loader s Working Device;裝載機工作裝置動臂框架工作狀態的力學分析
11.Reliability Analysis of Working Arm Mechanism of Supporting Disc Forming Mahine and Its Improvement支盤成形機工臂工作機構可靠性分析及其改進
12.Research on Automatic Control System of Working Mechanism of Boom-type Roadheader;懸臂掘進機工作機構自動控制系統的研究
13.The Supporting Characteristics Analysis of ZL80G Type Loader Working Attachment Boom Cylinder;ZL80G型裝載機工作裝置動臂油缸支承特性分析
14.The Loader Stress Analysis of the Arm of the Working Device Based on ANSYS;基于ANSYS的裝載機工作裝置動臂應力分析
15.Analysis and Modeling of Mechanical and Hydraulic System of Roadheader Manipulator懸臂式掘進機工作機構機液系統分析與建模
16.Dynamic Analysis of Hooklift Working Device Based on Virtual Prototype基于虛擬樣機的拉臂車工作裝置動力學分析
17.The cylinder head carries the valves, valve springs and the rockers on the rocker shaft, this part of the valve gear being worked by the push-rods.氣缸蓋攜帶閥門，氣門彈簧和在搖臂桿上的搖臂，這部分的氣門傳動機構通過推桿工作。
18.COMPARISONS AND ANALYSES OF SWEEP ARM AND DIRECT ARM SMASHING;大拉臂和直臂扣球兩種揮臂動作的比較分析
相關短句/例句
boom operation動臂工作
3)articulated boom platform曲臂工作臺
4)boom work light動臂工作燈
5)working arm mechanism工臂工作機構
1.Reliability lost type of working arm mechanism for supporting disc forming machine is analyzed.分析了支盤成形機工臂工作機構失去可靠性的形式 ,研究了工臂工作過程中的受力狀況 ,結果表明 :銷軸承受的兩種軸向力是使銷軸定位裝置損壞及銷軸脫落的主要原因 ,最后介紹了兩種成功的改進設計方案。
6)boom working rate吊臂工作幅度
延伸閱讀
13號染色體長臂部分單體綜合征13號染色體長臂部分單體綜合征13q partial monosomy syndrome 本征為D組13號染色體中的一條長臂部分缺失而引起臨床畸形。Carmichael等認為13號染色體長臂缺失很可能來自雙親之一的染色體異常。計雪文等認為可能是雙親之一的生殖細胞形成過程中或合子第一次分裂中，由于某種因素的影響使一個13號染色體在q21處發生斷裂，而后丟失斷裂的片段q22-qter的結果。其中與臨床有密切關系的為位于長臂中段中的q14陰性帶上有視網膜母細胞瘤的基因，故長臂缺失可并發視網膜母細胞瘤。表現為小頭畸形、寬而顯著的鼻前額骨、眼小、眼距寬，內眥贅皮、眼瞼下垂、上門齒凸出、小下頜、頸短、肛門閉鎖或會陰瘺和拇指發育不良或缺如。
